Saturday, January 8, 2011

C.O.G. Blog

Marcus Fenix: Gears of War 2 Armor

Ever since I made the Lancer (pictured below), I've wanted to make the C.O.G armor to go with it. Material costs, time and lack of a suitable work shop have always prohibited that. That is until the advent of EVA foam mats! Recently many people have been using floor mats as a material for creating armor, and other costumes.

Here is the original Lancer that attaches to my paintball gun (Tippmann A5)

...and here is the final Lancer prop.

Since they're incredibly cheap, easy to obtain, and simple to work with, I decided to take a crack at making my own armor.




After doing some test runs with poster-board, I realized I needed to have a mannequin in order to test the fit and make sure everything was proportional. I created this one by putting on an old t-shirt, and having my wife duct-tape me from belt to neck. Then, she cut down my back so I could get out. I taped up the back again and stuffed the whole thing with some old sheets.

Here's the entire set of tools needed to make the armor. Very easy, very cheap.

Next, I created the neck seal. I planned to build everything off it's scale. After that, I started to lay out the shapes of the chest piece with poster-board. Once finalized, these shapes would be templates for cutting out the EVA foam.

Once the major shapes were laid out, I decided to start cutting them out of the foam. The black foam is 1/2" thick. I used a box cutter and many, many blades. 

Some of the templates were changed on the fly. I had to adjust and re-do some of them to be more accurate and to fit together better. After all,  I'm no barrel-chested, heroically-proportioned, meat-head of a videogame character. 

 The idea here was that I would create a base "undersuit" on top of which I would lay out the actual armor plates. This would allow for the grooves between the plates and more flexibility for fitting and customization.

After I ran the material around the waist, I cut it on both sides and mounted some clasps so that I could get in an out of the armor.




Here's the finished "undersuit."

Here, I've started placing the first few pieces of actual armor. In this case, I'm using 3/8" mats. 

As before with the undersuit,  in order to get the shape right before I start cutting into the mats, I used paper, and poster board to make templates. Once I'm satisfied with a shape by pinning it in place, I cut the shape out of the foam. It's a lot of trial and error, and a lot of taping bits of paper together.





For the front end of the shoulder "straps" I used some styrene.

These are the templates I used for both the undersuit and many of the armor plates.

Here, I removed the shoulder straps to cut out the slits where the blue lights come from.



Starting to add some detail to the arm holes.

I attached all the armor plates using some webbing and hot blue. I attached the plates to the undersuit using Velcro strips. 

I had the idea that the undersuit could be a base for all future Gears of War armor. I could later, return to this project and make GOW 3 armor right over my existing undersuit.



This is the undersuit with all the Velcro strips

The groove down the middle was made with a soldering iron and a metal ruler. I also rounded off some of the edges with a dremel using the sanding barrel bit. You have to very careful. The Dremel can slip very easily and it will dig into the foam = piece ruined. If you sand in the direction the bit is spinning, it's much easier to control.

This is the main piece for the back, and two more side pieces. I shaped the back piece by bending it and working it while holding it over the burner on my stove. Then I threw it in the freezer for a few minutes. It works quite well actually.

For the more intricate details on the back, I got some craft foam. It's available at any major craft store. It's 2mm thick and not rigid at all.

Despite the craft foam colors shown above, I actually used mostly black and white sheets so far.
Here's the back plate with some added details

I cut into the existing foam here so that I could sink pieces into the hole to create a slope

You can see now that those pieces are pressed into the holes I cut earlier. I also added the base for that main box thingie in the middle of the back.

I decided to re-do the entire back plate. What you see above is not what I want, so I here's the progress on the new back plate:

This is the beginning of the box thingie on the center of the back.



Here, I started using craft foam to create the finer details of the armor plating.


These straps that come from under the arm and terminate at the bottom of the back were the most re-done pieces so far. It was a difficult transition that required the back plate and the rest of the piece to be perfectly lined up so that gaps would not reveal themselves later. I finally got it though. I also burned the grooves into those pieces.




Here I've started to create the template for what I call the "fanny pack" near the top of the back

It was a tough shape to get down, but eventually it came together. Unfortunately I'm out of the thin craft foam so I can't finish it right now. I used 1/4" craft foam sheets to create this shape.


Since I'm out any large pieces of the 2mm, craft foam, I moved on to the front buckle and belt assembly.



The belt. It is every bit as tedious as it looks. And I'm out of the brown foam so we stop here for now.



Here, I've started on the shoulder pads.


To shape the shoulder pads, I used the stove top to heat shape them, then I pushed them into this bowl. Still in the bowl, I put them in the freezer for a few minutes.


Once again, I'm re-doing the entire back plate. Hopefully for the last time!


I'm also re-doing the "fanny pack." This time, I carefully glued together little strips of foam to form the shape. To give it rigidity, I poured some urethane resin and slushed it around.



 At this point, I was not happy with the overall shape of the chest piece. I decided to scrap the black "under armor" and re-do a lot of the major pieces.




I mounted these buckles onto the top of the shoulder plate to attach them to the rest of the chest piece.
This allowed me to detach the back plate in order to get this thing on me.


Starting to draw out all the panel lines and rivets.

The neck piece.


Much, much better now.







Now to the belt.


And the boots. 

It was at this point in the project where I stopped taking pictures. I was running out of time. The only  major thing that's missing the boot construction. It was pretty tough to get the right shape, but they ended up turning out great. I also made the thigh plates, cod piece, and the wrist thingies. The elbow pads where just slightly modified, small knee pads from Home Depot. 


I also never really got a chance to take any proper final pictures. This is what I have though:


After Halloween (2011), I went back and added the rest of the decals. Thin blue circles on the chest speakers, blue stripes on the thigh plates, and those really cool bird insignia on the shoulders. I also added lights to the shoulders.

In the end, I think it turned out fantastic. Now, maybe one day, I'll take some real pictures.



11 comments :

  1. If I may ask, where did you get the blue-prints for the armour? I've been very unlucky in trying to find my own, I know for a fact I can't use pepakura as I have a mac and pepakura designer doesn't work on mac. Can you provide any support if possible, I understand you are busy, and can't respond but if you can thank you in advance.

    Regards,

    A Gears Fan from the UK

    P.S. Your armour is frickin' awesome

    ReplyDelete
    Replies
    1. Hey there, thanks! Just click on the image of the different views of Marcus. That's pretty much the blue-prints right there!

      Delete
  2. I have to say that I think your Deus Ex is awesome!!! I am currently embarking on making my first armor outfit and found your website useful. I am sure I will make mistakes....but that's what's it all about! :)

    ReplyDelete
  3. hey sloan just wondering if you still had the armor if so how much would you sell it for or make it for?

    ReplyDelete
  4. Hey Alex. I would sell the armor for 2k. It would be a lot more if you wanted me to make you your own set since it took almost a year working on and off on it.

    ReplyDelete
  5. ok thanks mate ill give it a try first n see how it goes

    ReplyDelete
  6. This comment has been removed by a blog administrator.

    ReplyDelete
  7. Hey there sloan I'm a huge gears fan an i thank you for this walk through I'm gonna follow this but add some bc I'm doin Marcus in gears 4

    ReplyDelete
  8. Hey what kinds of paint did you use for the project

    ReplyDelete
  9. This comment has been removed by the author.

    ReplyDelete